SBH-2-HH
SBH Series are self-leveling heaters and dispensers for plates and heat retentive devices (our Diamond D-8000 wax base) used in tray make up systems. An adjustable thermostat makes the unit compatible for low and high heat applications.

Only Piper's equipment has the advantage of FoodSafe technology and certification. This ensures that your food is kept "out of the DANGER-ZONE." Food spoilage occurs mainly because of rapidly accelerated bacteriological activity within the 40F-140F "DANGER-ZONE."

Since there is no simple way of knowing when the degree of contamination has risen to a level which could result in illness or death, chilling or freezing food rapidly is the only FoodSafe answer. FDA & HACCP regulations permit a maximum of 6 hours to chill food from 140 to 40 degrees, while some states now permit only 4 hours. This is 6 to 8 times faster than what traditional refrigeration equipment can accomplish.

 
   F_1   

MODEL NUMBER

  • SBH-2-HH
  • SBH-3-HH

CONSTRUCTION
The exterior shall be constructed of 304 high nickel 18-8 stainless steel with the frame constructed of 18-gauge, the side and front panels constructed of 20-gauge, the back panel constructed of 16-gauge and the base constructed of 14-gauge with a "H" frame reinforcement of formed "U" channel construction. Two (2) and three (3) silo models shall be available. Each tube shall hold approximately 50 bases or plates.

The fully insulated lids shall be constructed from 16-gauge stainless steel with a gasketless design. Lids have no hinges and can be hung on brackets during operation. The dispensing system shall be a cantilevered design with seven (7) heavy-duty field-adjustable springs to accommodate a variety of bases, plates and special high heat plastic serving ware.

The full perimeter "Bloc-Guard" bumper designed with a bottom "L" stainless steel reinforcement bracket to allow heavy long term use and 5" polyurethane non-marring swivel casters (2w/ brakes) shall be standard.

The heating system shall be a forced air convection design that circulates thermostatically controlled super heated air evenly through the fully insulated cabinet. The dual voltage unit shall be designed to draw 3200 watts at 240 volts with 13.5 Amps and 3000 watts at 208 volts with 14.5 Amps.

Control System:
The programmable electronic system has a large VFD Display and allows the operator to set the unit for manual start or automatic start. The real time clock will help the operator to set exact starting times for each cycle. Each compartment is heated by an independent direct forced hot air heating system which incorporates its own set of thermostatic controls to maintain the bases at 225°F. The heating system recirculate the hot air horizontally to ensure rapid and efficient heating of the bases. Temperature control is fully automatic, with no need for manual settings. Full heating of the bases is accomplished in 75 to 90 minutes.

Initial heat-up of a fully loaded unit shall be approximately 2 hours or less with reheat cycles to be 1-1/2 hours depending on wax base design.

STANDARD FEATURES

  • Heavy-duty 304 high nickel 18-8 stainless steel construction
  • 5" Swivel Plate Casters
  • Full perimeter "Bloc-Guard" bumper as standard
  • 3200 watts of converted forced air heat for faster heat up (thermostatically controlled)
  • Field adjustable thermostat
  • Gasketless lid seal design to maintain heat
  • Self-leveling, field adjustable spring dispensing design allows easy access to bases & plates
  • Two & three silo configurations
  • Holds 90 or 135 Diamond D Series wax bases - other base configurations may vary in quantity
  • Exterior control protection hood
  • Hinge-less lid
  • Lid hangers

Specifications



 

Model
# of
# Tubes
Approximate
Capacity
ea. tube/total
D
W
H
208V
3000W
240V
3200W
Phase
NEMA
Plug #
Heat
Limit
Shipping
Weight
SBH-2-HH
2
45/90
26.69"
38.69"
40.10"
14.5
13.5
1/60Hz
6-20P
High
300 lbs.
SBH-3-HH
3
45/135
26.69"
51.69"
40.10"
14.5
13.5
1/60Hz
6-20P
High
425 lbs.

Unit shall come with 6' #14-AWG cord set for 208/240V applications and a NEMA 6-20P plug.

Downloads

Filename Description Date Added File Size
  2008 Spec Sheet Base or Plate Heater
 06/03/2008 471.6 KB